How to install fingerprint lock fingerprint lock installation method and precautions

Fingerprint door lock is a high-tech product. Do you know how to install a fingerprint lock? First, select a suitable installation location, and attach the installation template of the random belt to the door to ensure that the sticker is flat. Then, the line is marked, and the high line is marked on both sides of the door and the door frame according to the size shown in the installation die, and the contour line of the hole position and the center line of the hole hole are marked on the door. Then drilled, using an electric drill to drill 4 mounting holes of 8MM, and 34MM diameter wire holes and 20MM square shaft holes.
First, the fingerprint lock installation instructions
1) Fingerprint door lock is a high-tech product. The environment in which the door lock should be used plays an important role in the normal use of the door lock, especially in the environment where dust or air contains high corrosive substances, which will greatly affect the door lock. Normal use. Therefore, it is recommended to install the door lock after the room has been renovated, in order to facilitate the normal use of the door lock and extend the service life of the door lock.
2) After the installation and debugging of the door lock is completed, please register the administrator in time to facilitate the better use of the fingerprint door lock. We recommend to register a fingerprint or a set of passwords when registering the fingerprint so that the fingerprint may wear out. In the case of normal opening.
3) The quality of the fingerprint door lock installation directly affects the normal use and service life of the door lock. It is recommended that experienced personnel install it and install it in strict accordance with the company's installation standards, and may not change it at will.
4) Fingerprint lock is the perfect combination of world-tip biometric technology and traditional electronic door lock. In order to make you feel better and more advanced, please read the operating instructions carefully before use.
Second, the fingerprint lock installation and removal of the door lock
This section describes the procedure for installing and removing a fingerprint lock. Unless otherwise indicated. Otherwise, the following conditions are assumed to be met at each process:
1 The right door is selected: wooden door, door thickness requirement: 40-60mm.
2 Please confirm the door opening method and lock cylinder again. There are four ways to open the door: left inner opening, left outer opening, right inner opening and right outer opening (the person is standing outside the door and the door is standard, the rotation axis of the door is The left side of the door is left open, the right axis of the door is right open on the right side, the inner door is opened in the door, and the door is opened outward. Cylinder: The left outer lock cylinder is the same as the right inner open lock cylinder. The left inner open lock cylinder is the same as the right outer open lock cylinder.
3 You have basic carpentry skills to open holes in the right place.
4 You have already read it (product manual).
5 The mounting assembly can be replaced by performing the removal process in reverse order.
Third, the fingerprint lock installation tool
Performing the steps in this manual may require the use of the following tools: an electric drill with 8MM, 16MM, 20MM, 25MM drills. l woodworking chisel l flat mouth screwdriver l plum flower slot screwdriver l ruler l line pen
Fourth, the door lock installation steps
Choose a suitable installation location, and attach the installation template of the random belt to the door to ensure that the sticker is flat.
1. Marking: Mark the high line on both sides of the door and the door frame. According to the size shown in the installation die, mark the contour line of the hole position and the center line of the hole hole on the door, and drill out the mounting holes according to the dimension. The door lock can be installed.
2. Drilling: Use the electric drill to drill 4 mounting holes of 8MM, and the 34MM diameter wire hole and 20MM square shaft through hole. Use the electric drill and wood chisel to open the 25X50MM square hole 95X30X5MM recessed table.
Install the lock cylinder: Check whether the hole positions of the lock body are consistent with the installation hole position, press it into the lock cylinder, and then tighten it with screws. After completion, please check the pop-up condition of the lock tongue.
Install the outer lock body: pad the waterproof rubber pad, wear the wire through the perforation and position the mounting holes, first use 2 screws, pass the mounting plate in the door, and fix the door front body part on the door in the lower part.
3. Install the rear lock body: Connect the connecting wires of the front and rear lock body according to the correct interface, insert the wire into the socket of the lock body according to different joints, and then connect the knob square shaft to ensure the front and rear lock body and the lock core are reliable. Connect, and finally fix the lock body to the door with screws.
4. Install the battery and battery cover: After inserting the battery into the battery case in the correct positive and negative directions, close the battery cover.
5. Function detection: After the installation is completed, refer to the user manual to check whether all relevant functions of the lock are normal.
Five, fingerprint lock installation precautions
Because the opening method of the lock is different, the hole on the mounting die is different. Therefore, before the scribing, the holes on the mounting die must be determined according to the opening mode of the lock.
Pay special attention: lock the front and rear body wires, the direction of the socket and the plug to ensure the connection is correct. Before installation, first determine the installation height of the lock. After determining the height, attach it to the corresponding position with the installation mold, and then use a pencil to draw the position where the hole is required. When installing the hole, the mounting flange must be perpendicular to the door frame. Otherwise, the lock body cannot be perpendicular to the door after installation. The lock cylinder is generally required to be installed in the middle of the door thickness. After opening the hole in the door frame, be sure to clean the wood chips or other foreign matter in the hole to prevent the door from falling into the lock body when the switch vibrates.
Keep the lock body clean and tidy: Do not drop abnormal things such as wood chips or iron filings from the lock body gap into the lock body, causing short circuit of electronic components or jamming of other components. Cylinder installation: After the lock cylinder is installed in the mounting hole, the surface of the lock cylinder cannot be higher than the surface of the door frame and should be in the same plane.
Installation of the gusset plate: The hole position of the gusset plate must correspond to the position of the lock tongue. If the correspondence is not good, the door will be loose or cannot be closed, and the safety tongue cannot be inserted into the hole of the gusset plate. Installation of the lock body: the screw must be in place and there should be no gap between the lock body and the door. Wire connection: The wire connection must be correct and the connection is secure, otherwise the door lock will not work properly.
Eligibility criteria:
The lock body is perpendicular to the door frame and has no tilting phenomenon; there is no looseness after the door is closed; the handle is flexible; the reset is normal; the lock tongue pops up normally without jamming; when the door is closed, the door can be closed with a light door (if a large force door is required) In order to close the door or rebound, it is judged that the installation is unqualified); each function is normal.

Removable anti-theft Wheel Bolts are used with an internal tooth shape to guard against theft. Their tooth shape is different, so that each anti-theft wheel lock bolts are not same and it will be safer for end users. Normally, we provide the Wheel Nuts & Wheel Bolts with several different shapes of keys.

Some cars(such as BMW, Mercedes-Benz, Saab, Volkswagen) use Wheel Lug Bolts instead of Wheel Nuts, which are screwed into a threaded hole in the wheel's hub and tighten it hard. You have to check the hex size,thread length and seating types when you're ready to buy the Wheel Bolts.

Wheel Bolts

Carbon Steel Wheel Bolts,Wheel Lug Bolts,Wheel Bolts And Nuts,Tire Bolts,Locking Nuts And Bolts

Ningbo Best Way Auto Accessory Co., Ltd. , https://www.autoaccessorycn.com