Did you pay attention to floor heating?

Nowadays, more and more people choose to warm up in winter heating. It can be seen that the floor heating has been deeply rooted in people's hearts. Everyone has a certain understanding of floor heating products. They think that as long as they have bought a good product, they can enjoy a comfortable winter in the future. People often fall into this misunderstanding, and it is far from enough to place floor heating only on the quality of the product. Floor heating is also a top priority. In particular, the construction quality of the floor heating insulation system is often overlooked. Today, the Shanghai floor heating experts took everyone to discuss some of the considerations in the construction of the floor heating insulation system.


Ground insulation system construction preparation

1. Before the laying of the ground insulation system, the construction of the ground wall must be completed and the foundation leveled. There is no other work in the site.

2. The temperature in the construction room should meet the requirements for proper use of the pipe, because the ambient temperature is closely related to the bending radius of the pipe.

3. Clean the floor and walls, and use a level gauge to verify the flatness of the ground. The height difference within 1 meter is less than or equal to 5 millimeters. The wall or ground protruding part is removed with a shovel, and the ground pit is filled with concrete.

4, the bathroom and the villa should be done at the bottom of the waterproof layer or laying moisture-proof membrane.


Floor heating special boundary insulation construction

1. Before laying the boundary insulation strip, clean the wall, ensure the flatness of the wall surface, and avoid the insulation strip falling off in the process of construction and use.

2. The boundary insulation strip shall be affixed on the wall surface and the cylinder surface at the intersection of the ground in the heating area. The boundary insulation strip shall have excellent fastness to ensure that it will not fall off during use.

3, the border insulation strip should have a thickness of 8 mm, the boundary insulation strip must have a certain degree of flexibility, to ensure that the backfill layer plays a role in buffering after thermal expansion, the maximum compression is 5 mm. The extruded extruded board does not allow to replace the boundary insulation strip.

4. The lap joint should be used at the junction of the boundary heat insulation strip, and the length of the lap joint should not be less than 3 cm.

After reading the above information, you must pay attention to each step when installing the floor heating, especially in the installation process, the need to pay attention to matters must be careful.

EVA Moulding Machine For Shoes

The machine is fully hydraulic and automatic operation expect taking product. And coordinate humanized parameter computer operation interface with database to provide quick and exact terms of production, the modern top injection-molding machine can produce EVA mid soles (wedge), slippers, sport protectors and various kinds of shoe accessories. It`s allowing to match the other kind of mould and material to produce the other products.

Full-Automatic Foam EVA Injection Moulding Machine

Advantage:

1. Low operation height;

2. Extra Height opening stroke;

3. Mould thickness adjusting mechanism;

4. Rapid mould opening;

5. Speedy injector MOVENMENT;

6. Energy saving design;

7. Space saving design .

Main Technical Parameter

Work Station	Station	6
Clamping Force	ton	180
Mould Plate Size	mm	2(290*550)
Mould Height	mm	100-210
Mould-Opening Stroke	mm	350
Injection System
Injector		2
Diameter of Screw	mm	Φ60
Injection Cap(Max)	cc	920
Injection Pressure	kg/cm²	0-130
Injection Speed	cm/sec	0-10
Rotating Speed of Screw	r.p.m	0-190
Temperature Control	section	4
Electricity Consumption
Heater Barrel	kw	9.8x2
Heating Plate	kw	76.8
Hydraulic System	kw	40.5
Vacuum Pump	kw	1.5
Cooling Fan of Barrel	HP	1
Total Electricity	kw	138
Oil Tank Size	L	800
Machine Weight	kg	23800

EVA Moulding Machine For Shoes,Full-Automatic EVA Injection Moulding Machine,EVA Double Foaming Moulding Machine,EVA Moulding Machine

SHIJIAZHUANG LONGXUAN TRADING CO., LTD , https://www.longxuanmachines.com