Heat balance calculation method for refrigerated trucks

Heat balance calculation method for refrigerated trucks

How to calculate the thermal balance of the refrigerated truck's insulated cargo compartment, now we will use the commonly used 4-meter refrigerated truck as an example to analyze: 4 meters refrigerated truck insulation compartment wall panels are insulated, due to the goods There is a certain temperature difference between the inside and the outside of the insulation wall of the compartment, so there are three processes in which the heat is transferred from one side of the insulation wall to the other side of the cooling fluid: the heat from the high temperature side is transferred to the high temperature side. The surface of the wall, the thermal conductivity in the insulating wall, that is, the heat is transferred from the high temperature side surface of the heat insulating wall to the low temperature side surface, and the heat is transmitted from the low temperature side surface of the heat insulating wall to the low temperature side air. Take the insulated cargo compartment as an example. In general, the outside temperature is higher than the inside temperature. The heat is transferred from the air outside the cabin to the outer skin surface of the heat insulation wall, and then transmitted to the inner skin surface through the outer skin heat insulation layer and the inner skin material, and then transmitted from the inner skin surface to the air in the cabin. go with.
1) =K. F(-)=0.4×13.83×10=55.32 (2-1)
In the formula: k-insulation compartment total heat transfer coefficient, W/(.K)
F- heat transfer area of ​​the insulated cabin,
- Air temperature outside the insulated cabin, K
- Air temperature in the insulated cabin, K
2) Heat flow into the compartment due to air leakage caused by gaps in the cargo compartment of the 4m refrigerated truck
The following empirical formulas are commonly used in actual calculations:
= (0.1 to 0.2) = 0.1 × 55.325.532 (2-2)
Under normal circumstances, take = 0.1 serious cargo leakage, take = 0.2
3) Heat flux of solar radiation
=K(-)=0.4×6.915×20×0.5=27.66 (2-3)
In the formula: - The area where the cargo compartment is exposed to solar radiation is generally taken from 35% to 50% of the heat transfer area.
- The average surface temperature of the cargo compartment affected by solar radiation, taken as = +20, K
The T-cargo is exposed to the sun every day for 12 to 14 hours.
4) Unload the incoming heat from the door
=f(+)=0.75×170.72=128.04 (2-4)
In the formula: f-opening frequency coefficient. Do not switch during transportation, take f = 0.25, open the door 1 ~ 5 times, take f = 0.5, open the door 6 ~ 10 times, take f = 0.75, open the door 11 ~ 15 times, to f = 1.
5) Heating value of goods loaded in the cargo compartment
= =1000×15=15000 (2-5)
In the formula: - The quality of a certain cargo in the cargo compartment, Kg
- Heat of a certain cargo in the cargo compartment
6) Heating capacity of fans and lights in the cargo compartment
=(+)=2900×=120.8 (2-6)
Where: - The power of the lamp, W
- Average daily lighting time, h.
7) Power consumed when the cargo compartment body is precooled
===22500 (2-7)
In the formula: -The quality of the cooling part of the cargo compartment, Kg
- The average specific heat of the cooling section of the cargo compartment, J/(Kg.K)
- The difference between the outside temperature and the inside temperature, K,
t - time for precooling cargo bed, h.
8) Heat flow taken from pre-cooling cargo in cargo compartment
=()=(10001500+502500)=12500(2-8)
In the formula: - Quality of goods in cargo compartment, Kg
- The quality of the carton container, K
- The specific heat of the packaging container, J/(Kg.h), j = 2500 J/(Kg.h)
When a refrigerated automobile transports fruits, vegetables and fresh eggs, the refrigeration unit is required to pre-cool the insulated cargo compartment and cargo at the same time. At this time, the heat load of the refrigeration unit is:
Q=+++++++=23kw (2-9)

Considering that the refrigerating device cannot work continuously, the safety factor n should be considered when designing and selecting the heat load, that is, the heat load is n Q. Generally, the refrigerated car takes n=1.3 to 1.5.

[More Special Vehicles Inquiry]: 4000 118 130     Http://
[Company Name]: Cheng Li Special Purpose Vehicle Company Limited
[Corporate Address]: Chengli Automobile Industrial Park, South Suburbs, Zengdu District, Suizhou City, Hubei Province
[fixed telephone]: 0722-3801919
[mobile phone number]: 138 7289 7777 139 7179 3909
[Contact QQ]: 928456772
[Email address]:

High pressure water gun is pressure washer, high pressure water jet cleaning machine known.
Scope:
1. All kinds of motor vehicles, construction vehicles, construction machinery and agricultural machinery and equipment, cleaning and maintenance products such as washing cars, bulldozers, concrete mixers, tractors. Conservation is a personal and small vehicle unit cleaning the car, motorcycle the most ideal cleaning tool. Facades, floors, baths, swimming pool cleaning, for doors and windows, floors, toilet, oil and artificial hard-to-corner is particularly effective. Food-processing, food processing machinery as well as hotels, restaurants, kitchens decontamination. More than 500bar pressure washer can be super concrete cutting hair, higher pressure pressure washer can even cut, chiseled concrete various labels.
3. The food-processing, food processing machinery as well as hotels, restaurants, kitchens decontamination.
Water cannons widely used in industrial dust, clean city streets, city crust Clear, wash clean, train cleaning, air cleaning, food processing, livestock health and other fields.
High Pressure Hose, flexible pipe can withstand the pressure. Widely used in industrial production and living.
High-pressure hose into: fiber reinforced polyurethane hose, fiber reinforced nylon hose, wire reinforced polyurethane hose, wire reinforced nylon hose, hose wire winding resin, food grade hose.
Only under pressure to complete the hand with measuring binding hose or disconnect. Compact. High working pressure.
High pressure quick connector is used to connect primarily used for high or low pressure fluid sampling system and the system pressure testing.
High pressure quick connector one-way valve will be sealed passage, not oil, of course, and other effects: If there are air bubbles in the system can take the pick head open and emit gases; convenient test cylinder, valve block, and so on.

Gun, Lance & Hose

Trigger Gun,Pressure Washer Lance,Pressure Washer Hose,Under Water Cleaner Single Jet Algae Cleaner,Sailing Boat Cleaner,Twin Jet Chain Cleaner etc.

NINGBO HAISHU OMWAY MACHINERY FACTORY , http://www.omwindustrial.com